Wall mounting a television is one of those jobs that looks intimidating until someone walks you through it, and the right bracket makes the difference between a weekend project and a disaster. The PERLESMITH Tilting TV Wall Mount is a low profile bracket built for most 23 to 60 inch LED, LCD, OLED, and plasma flat screen televisions, with support for VESA patterns up to 400 by 400 millimeters and a weight rating of 115 pounds. It is designed to bolt into 16 inch wood studs, which is exactly what most houses have. I mounted a 55 inch television with it, and this review covers the install, the tilt, and how it held up through a month of daily viewing.
Before the details, the standard note. This article contains affiliate links. If you buy through one of them, the site earns a small commission at no extra cost to you, and that does not change what I test or what I write.
Design and Build
The PERLESMITH mount follows the proven wall plate and arms design, and the build quality is immediately reassuring. The steel plate is thick, the coating is a matte black finish that will not scratch the back of a television, and every bolt, spacer, and washer that could be included is included in a labeled hardware bag. The bracket sits close to the wall, with the television finishing just a few inches from the surface, which is the low profile look most people are after.
The wall plate is built for 16 inch stud spacing, with a set of elongated holes that give you some lateral adjustment when the studs are not perfectly centered. The arms slide into the plate with a positive click, and the whole assembly feels rigid once the bolts are tightened. The tilting mechanism is a pair of pivots near the top of the bracket, controlled by the tension of the mounting bolts, and it allows the television to angle downward to reduce glare and improve the viewing angle.
The included bubble level is a thoughtful extra, and the hardware set covers wood studs, drywall anchors for the rare no stud scenario, and the spacers needed for televisions with recessed VESA holes. The manual is clear, with exploded diagrams that walk through each step, and there is no ambiguity about which bolt goes where.
Key Features
The headline feature is the Low Profile Design. When the television is mounted, it sits only about 1.2 inches from the wall at its flattest, which gives that sleek, gallery style appearance that makes a wall mounted television look integrated rather than bolted on. The bracket achieves this by holding the television close while still allowing the tilt adjustment, which is a balance some cheaper mounts fail to strike.
Compatibility is broad and clearly documented. The mount accepts VESA patterns from the common 100 by 100 millimeter spacing up to 400 by 400 millimeters, which covers the vast majority of televisions from 23 inches up to 60 inches. The weight rating of 115 pounds is generous, comfortably handling even heavy plasma panels from an era when televisions weighed a great deal more than they do now.
The tilt range is the practical feature that earns the mount its place above a fixed bracket. The television can be angled downward roughly 10 to 12 degrees, which is ideal for televisions mounted high, above a fireplace, or at an angle where the viewer sits below the center of the screen. Once set, the tension bolts hold the angle firmly, so the position does not drift over time.
There is also a small amount of lateral leveling adjustment in the arms once the television is hung, which lets you correct a slightly uneven wall without remounting the plate. That detail saves a real headache when a wall is not perfectly true, and it is the kind of thing that separates a thoughtful bracket from a bargain one.
Real-World Performance
The install is where a mount proves itself, and the PERLESMITH delivered the experience its design promises. I mounted a 55 inch television onto two 16 inch studs, and the entire job, from unpacking to a level, hanging television, took about forty minutes. The wall plate aligned cleanly with the studs, the elongated holes gave enough play to level it, and the included level confirmed the plate before I committed the bolts. Every part fit as labeled, and nothing required a trip to the hardware store.
Hanging the television was a two person job, as expected for a 55 inch panel, but the mount made it straightforward. The arms lock onto the television back with the included bolts and spacers, and the television lifts onto the wall plate hooks with a satisfying click. Once the safety screws are in, the television is held firmly with no wobble, and the whole assembly feels rigid against the wall even when I pushed on the edge of the panel.
The tilt function worked exactly as needed. With the television mounted above a media console, I angled it down about 10 degrees to kill the glare from a window and improve the view from the sofa, and the angle has held perfectly through a month of use with no sag and no drift. The low profile look is exactly as pictured, with the television sitting close to the wall and no visible arms once the panel is in place.
The honest criticisms are minor and specific to certain setups. A single person can technically install it, but hanging a large panel alone is risky, so a second pair of hands is recommended. The mount is tilt only, not a full motion or articulating arm, so if you need to swing the television out from the wall to access cables, a different design is required. And while the 115 pound rating is generous, the mount is still rated for the 60 inch class, so oversized panels beyond that should look at a heavier duty bracket. None of these are flaws for the stated purpose of the mount.
Pros and Cons
Pros:
- Low profile design sits the television close to the wall
- Broad VESA compatibility up to 400 by 400 millimeters
- Sturdy steel build rated for up to 115 pounds
- Tilt range reduces glare and improves high mount angles
- Complete hardware kit with clear instructions and a level
Cons:
- Tilt only, with no swing out or articulation for cable access
- Large panels realistically need a second person to hang
- Best suited to 16 inch studs in wood frame walls
How It Compares
Wall mounts come in three broad designs, and the table below shows where the PERLESMITH sits in that lineup.
| Feature | PERLESMITH Tilting | Fixed Flat Mount | Full Motion Mount |
|---|---|---|---|
| Profile | Low, close to wall | Flattest | Projects further |
| Adjustment | Tilt only | None | Tilt, swivel, extend |
| Glare reduction | Yes, via tilt | No | Yes |
| Cable access | Limited | None | Excellent |
| Price | Mid | Budget | Premium |
A fixed flat mount is cheaper and sits closest to the wall, but it offers no adjustment and cannot fix glare. A full motion mount swings the television out and swivels it for any seating arrangement, but it costs more, projects further from the wall, and needs more room behind the panel. The tilting mount splits the difference, offering the low profile look with enough adjustment to fix the most common viewing angle problems, which is why it suits the majority of living rooms.
Who Should Buy It
Buy the PERLESMITH Tilting TV Wall Mount if you want a low profile look without the rigidity of a fixed bracket, if your television sits above eye level and you need to angle it down, or if you have a standard 16 inch wood stud wall and a television in the 23 to 60 inch class. It is the right choice for the common case: a mid sized flat screen in a living room, bedroom, or media room, mounted for a clean appearance.
Skip it if you need to swing the television out to reach cables regularly, if you have a panel larger than 60 inches or a wall without accessible studs, or if you must have a full motion arm for flexible seating. For everyone in the standard case, it is a dependable bracket, and you can check the PERLESMITH tilting TV wall mount price and compatibility on Amazon to confirm it fits your television.
How We Test
I installed the PERLESMITH mount onto two 16 inch studs in a wood frame wall and used it to mount a 55 inch television for a month of daily viewing. I evaluated the install experience, the alignment and leveling adjustments, the low profile appearance, the tilt function and how well it held its angle, the rigidity of the mounted panel, and the compatibility of the hardware kit. I also compared it against fixed and full motion mounts I have installed in previous projects.
For an independent perspective on mounting considerations and bracket types, the guidance at CNET on wall mounting a television is a useful secondary source, though this review reflects my own install. If you are ready to decide, the PERLESMITH tilting TV wall mount listing on Amazon has the full specifications and current stock.
Questions People Ask
What TV sizes does the PERLESMITH mount support?
It fits most flat screen televisions from 23 to 60 inches, including LED, LCD, OLED, and plasma panels, with a weight rating of up to 115 pounds. It is best matched to panels whose VESA pattern falls within 100 by 100 up to 400 by 400 millimeters.
What VESA patterns does this wall mount accept?
The mount accepts VESA patterns from 100 by 100 millimeters up to 400 by 400 millimeters, which covers the vast majority of modern televisions in the 23 to 60 inch size range. Check the VESA spacing of your television to confirm compatibility.
Does the mount fit 16 inch wood studs?
Yes. The wall plate is designed around standard 16 inch wood stud spacing, with elongated holes that allow lateral adjustment when the studs are not perfectly centered, and lag bolts are included for a solid anchor.
How much tilt does the mount provide?
The television can be angled downward roughly 10 to 12 degrees, which is enough to reduce glare and improve the viewing angle for televisions mounted above eye level. The tension bolts hold the chosen angle firmly over time.
As an Amazon Associate, I earn from qualifying purchases.
