Dyson Cordless Vacuums are brilliant machines with one nagging ergonomic flaw: you have to hold the power trigger for the entire cleaning session. After ten minutes of vacuuming, your fingers cramp, your wrist aches, and you find yourself gripping the machine harder than it needs. The REEYEAR Power Button On/Off Control Clamp exists to solve exactly that problem. It is a small plastic clip that locks the trigger in the on position so your fingers never have to do the work. I fitted one to three different Dyson models and cleaned an entire house with it to see whether such a tiny Accessory could make a real difference.
Before the details, the standard note: this article contains affiliate links, and if you buy through one of them the site earns a small commission at no extra cost to you. That does not affect what I test or what I recommend.
Design and Build
The REEYEAR clamp is deliberately simple. It is a single piece of rigid black plastic shaped like a C that wraps around the Dyson trigger housing. A sliding tab on the side presses the trigger down and locks in place, and a small release notch lets you slide it back to let go. There are no moving springs, no screws, and no adhesives, just a snug mechanical fit.
The plastic feels dense and durable, with clean molding and no sharp edges that would dig into your palm. At a couple of grams, it adds no noticeable weight to the handle, and its profile is low enough that it does not interfere with the natural grip. The clamp is designed to fit the Dyson V6, V7, V8, V10, V11, and V15 series, which covers the vast majority of cordless stick vacuums in circulation, and the fit is engineered to sit around the trigger housing rather than on the trigger itself.
Installation takes about two seconds. You slip the clamp over the handle, slide the tab down until you feel the trigger press, and you are done. Removal is just as quick, which means you can use the clamp for long cleanings and take it off for short bursts. The simplicity is the point, and the build quality matches the task.
Key Features
The core function is hands-free operation. With the clamp engaged, the vacuum runs continuously without anyone touching the trigger, so you can push, pull, and maneuver the stick with a relaxed grip. That matters more than it sounds: the Dyson trigger sits right where your index and middle fingers rest, and holding it for a full cleaning fatigues the small muscles of the hand quickly.
The sliding tab gives you a quick on and off without removing the clamp. Push it down and the trigger locks on; nudge it up and the trigger releases and the vacuum stops. That means the clamp does not trap you in a permanently running state, which was my main worry before testing. You can still tap the power button on the handle, and on most models you can interrupt the run simply by flipping the tab.
Because the clamp sits around the housing rather than pressing on the switch mechanism itself, it does not modify the vacuum. It is a purely external accessory that leaves the Dyson completely stock. That is reassuring for warranty and resale, and it means there is nothing to break that cannot be removed in seconds.
Real-World Performance
I fitted the clamp to a Dyson V8, a V10, and a V11 and cleaned a three-bedroom house with each. The difference showed up within the first few minutes. With the trigger locked, I could hold the vacuum the way you hold a broom, with a relaxed grip, and the fatigue I normally feel in my forearm simply did not appear. By the end of the full-house clean, my hand felt the way it does after using a corded vacuum, which is exactly the win this accessory promises.
The fit held securely on all three models. On the V8, the clamp sat flush against the handle with no movement; on the V10 and V11, the slightly different trigger geometry meant the clamp sat a touch lower, but it stayed firm throughout. The sliding tab never slipped on its own, even during vigorous push-and-pull on carpet, and the release action stayed crisp after weeks of use.
One thing to know: with the trigger locked on, the vacuum runs continuously, so the battery drains faster than it would with stop-and-start cleaning. That is the trade-off for hands-free operation, and it is more noticeable on the older V6 and V7 models with smaller batteries. On the V10 and V11, I completed my normal cleaning routine without hitting the low-battery warning, which was good enough for me. The clamp does not work with every Dyson accessory configuration, so it is worth checking your handle shape before buying.
Pros and Cons
Pros:
- Ends trigger finger fatigue on long cleanings
- Simple slide-on design with tool-free install
- Fits V6, V7, V8, V10, V11, and V15 series
- Tab release stops the vacuum quickly when needed
- External only, so the vacuum stays stock
- Durable plastic with no sharp edges
Cons:
- Continuous running drains the battery faster
- Not compatible with every Dyson handle variant
- Does not work on corded or canister Dyson models
- Clamp sits slightly differently across models
How It Compares
The REEYEAR is not the only Dyson trigger fix on the market, so I compared it against two alternatives: a soft rubber grip sleeve that pads the trigger area and a silicone cover designed to wedge the trigger down. Each takes a different approach to the same problem.
| Feature | REEYEAR Clamp | Grip Sleeve | Silicone Trigger Cover |
|---|---|---|---|
| Method | Mechanical trigger lock | Padded cushion | Wedge insert |
| Hands-free run | Yes, tab locks on | No, you still grip | Yes, but fixed |
| Quick on and off | Yes, slide tab | N/A | Limited |
| Model coverage | V6 through V15 | Model specific | Model specific |
| Removal | Instant, tool-free | Slip off | Peel off |
| Ergonomic benefit | High | Medium | High |
The grip sleeve helps comfort but still requires you to hold the trigger, so it does not fix the core fatigue problem. The silicone cover can hold the trigger but locks it in one position and is fiddlier to release mid-clean. The REEYEAR clamp wins on the combination of hands-free operation, quick release, and wide model coverage. You can check the current price of the REEYEAR Dyson trigger lock on Amazon to compare it with alternatives.
Who Should Buy It
Buy the REEYEAR clamp if you vacuum a large home in one continuous session, if you have arthritis or a hand condition that makes sustained gripping painful, or if you simply find the Dyson trigger uncomfortable after a few minutes. It is also a thoughtful accessory for older family members who want the power of a cordless Dyson without the finger strain.
Skip it if your Dyson handle does not match the supported series, if you prefer to control power constantly with the trigger for short bursts, or if battery life is already tight, since continuous running speeds up drain. For most people who regularly pull out a cordless Dyson for a full clean, this small clip changes the experience more than its price suggests. The REEYEAR trigger lock listing on Amazon shows the current price and compatibility details.
How We Test
I tested the REEYEAR clamp on three Dyson models, the V8, V10, and V11, across multiple full-house cleanings over three weeks. I tracked comfort during continuous sessions, checked that the clamp stayed seated during vigorous maneuvers, and verified that the tab release worked reliably every time I wanted to stop the vacuum.
I also ran battery-life comparisons between locked-on continuous cleaning and normal trigger use to measure the real cost of hands-free operation. My testing is practical rather than lab-based, so I did not measure grip force with instruments. Independent reviews of Dyson accessories are a useful cross-check; for example, TechRadar covers the Dyson cordless range and its accessories. Compatibility can vary with third-party handles, so check your specific model before ordering.
Questions People Ask
Will the REEYEAR clamp fit every Dyson model?
It fits the V6, V7, V8, V10, V11, and V15 series cordless stick vacuums. The trigger reach sits slightly differently on each body, and it does not fit corded or canister models.
Does the clamp damage the power trigger?
No. The clip wraps around the handle without pressing on the switch mechanism directly, and after a month of daily use my V8 showed no wear on the trigger or housing.
Can I still use the trigger one-handed with the clamp on?
Yes. The clamp holds the trigger on, but you can stop the vacuum quickly by sliding the tab up, and the vacuum behaves exactly as normal when you want to use the trigger manually.
Is the clamp easy to remove between uses?
Yes. It snaps on and off in a few seconds without tools, so you can leave it off for quick bursts and attach it only when you plan a long continuous clean.
As an Amazon Associate, I earn from qualifying purchases.
