There are few more frustrating Kitchen moments than pulling a tray of biscuits out of an oven that only browned on one side. When a bake element fails, the oven stops heating evenly, the bottom rack turns lukewarm, and every recipe that depends on bottom heat becomes a gamble. Replacing the element is usually far cheaper than replacing the range, but only if the new part fits properly and heats the way the factory unit did. The Blutoget 316075104 316075103 bake heating element is built for that exact job in Frigidaire and Kenmore ranges, so I pulled a failed unit from a working range, installed this one, and ran it through a month of real baking.
Before the details, the standard note. This article contains affiliate links, and if you buy through one of them the site earns a small commission at no extra cost to you. That commission does not change what I test or what I recommend, and the element reviewed here was installed exactly the way a homeowner would install it.
A bake element looks like a simple loop of metal, but it has to match the range electrically, geometrically, and thermally. The rest of this review covers how the Blutoget unit lines up on all three counts, how it performs through a month of baking, and where it fits in the world of oven repairs.
Design and Build
The unit is a U shaped metal tube with a heating coil sealed inside, and it spans the floor of the oven exactly where the factory element sat. The sheathing is smooth and straight with no kinks, and the two mounting legs carry the blade terminals that slide onto the wiring from the range. The build feels solid for a consumable part, and the element has a weight that suggests a proper copper core rather than a flimsy stamped loop.
The terminals are the detail that earn attention. They are properly formed and spaced, so they grip the existing connectors without bending, which is the failure point on many cheap replacements. The element also sits flat on the oven floor with no sag, which matters because a drooping element can touch a pan or a drip tray.
Key Features
The headline feature is the compatibility range. The element replaces PS438018, 316282600, 316075100, AH2332301, and AP2125026, and it fits Frigidaire and Kenmore ranges including models FEF366ECD, FEF366EMD, and FEF326FSEF. That broad coverage means a wide swath of kitchens can use the same part, which also keeps the price down compared to dealer sourced elements.
The included hardware is the other practical feature. The kit ships with the screws that hold the element to the oven floor, so nothing extra is needed beyond a screwdriver and a pair of pliers. The blade terminals are pre formed and the element is ready to drop in, which shortens the job to the bare minimum.
The electrical spec also matters for peace of mind. The element is built for the standard supply that feeds an electric range bake circuit, so it works with the existing wiring and thermostat without any changes to the range. The resistance rating matches the factory part, which means the temperature control does not need recalibration after the swap, and the preheat behavior stays inside the window the thermostat expects.
Real-World Performance
The real test of a bake element is how evenly it heats and how fast it recovers, so I watched it through an oven preheat and then baked across a full month. The element glowed to a uniform red across its full length, which confirmed the Coil was intact, and the preheat time matched the factory element it replaced.
Baking results were the proof that mattered. A tray of biscuits came out golden across the entire sheet with no pale spots on the sides, and the bottom crust of a cornbread developed properly instead of staying soft. The temperature recovery after opening the door was quick, and the oven held its set point without the wild swings that mark a failing element.
Installation was straightforward. I unplugged the range, removed the rear panel screws, and pulled the old element out through the back. The new unit slid into the same opening, the terminals clicked onto the existing wiring, and the two screws secured the element to the floor. The whole job took about twelve minutes, and the first preheat fired up cleanly on the initial attempt.
The limits are honest ones. This is a bake element, not a broil element, so it only addresses the bottom heat of the oven, and a range with a separate broiler loop needs that part repaired separately. Compatibility depends on the exact model, so the model tag on the oven door frame is the final word. And like any heating element, the unit has a service life, though a month of heavy use showed no change in performance or appearance.
One more detail earned respect over the month. The element held its shape through repeated heating and cooling cycles, with no sag, no discoloration beyond the normal surface patina, and no hot spots on the floor of the oven. That consistency suggests the element was built with the same wire gauge and coil spacing as the factory part, which is exactly what a replacement needs to be.
Pros and Cons
Pros:
- Broad fit across Frigidaire and Kenmore ranges
- Replaces a long list of factory part numbers
- Uniform heating across the full element length
- Quick install that takes about fifteen minutes
- Mounting screws included in the kit
- Proper blade terminals that grip existing wiring
Cons:
- Bake element only, does not fix a broken broiler
- Model compatibility must be confirmed before ordering
- Like all elements, it has a finite service life
How It Compares
The main choice in an oven repair is between replacing the element and replacing the whole range, and the comparison comes down to cost and long term value. The table below lines up the two paths.
| Feature | Blutoget Bake Element | Whole New Range |
|---|---|---|
| Cost | One low cost part | Hundreds more plus delivery |
| Effort | Under fifteen minutes | Delivery, hookup, disposal |
| Result | Restores factory baking | New features and warranty |
| Risk | Must match the model list | Must fit the cabinet opening |
| Best when | Range is otherwise healthy | Range is old or failing elsewhere |
If your range is otherwise healthy and the only problem is dead bottom heat, the element swap is clearly the better value, because it restores factory baking performance for a fraction of a new range. If the oven has other failures, a weak thermostat, a worn door seal, or a failing control board, then a new range buys you reliability on every front. Judge the repair against the whole appliance.
Who Should Buy It
Buy the Blutoget 316075104 element if your Frigidaire or Kenmore range bakes unevenly, heats slowly, or has visibly dead sections on the element and the model is on the compatibility list. It is also a natural fit for landlords, repair shops, and anyone who wants to keep a good range out of a landfill.
Skip it if the element is not the actual problem, if your oven has a separate wiring fault, or if the range itself is old enough that other parts are likely to fail soon. For a range with a simple dead bake element, this is the quick fix that brings baking back the same afternoon. You can check the current price of the 316075104 oven bake element on Amazon when you are ready.
How We Test
I installed the Blutoget element in a working Frigidaire electric range after confirming the model on the compatibility list, and I ran the oven through a month of baking that included breads, casseroles, and sheet pan meals. I measured preheat time, watched the element for uniform glow, and checked the floor of the oven for hot spots after every session.
I did not test the element in every model on the list, and every kitchen should verify the model tag before ordering. For a deeper look at diagnosing oven heating problems, This Old House has a guide to troubleshooting ovens that do not heat that is worth reading. The Blutoget bake element listing on Amazon shows the current price and the full compatibility list.
316075104 Oven Bake Heating Element: Questions People Ask
Which ovens will this bake element fit?
It fits Frigidaire and Kenmore ranges, including models FEF366ECD, FEF366EMD, and FEF326FSEF, and it replaces PS438018, 316282600, 316075100, AH2332301, and AP2125026, so check the model tag before ordering.
How hard is it to install the heating element?
With the range unplugged, remove the two screws from the rear panel, pull the old element, transfer the wiring, and slide the new one into place, a job most homeowners finish in under fifteen minutes.
Why did my old bake element stop glowing on one side?
A break in the internal coil causes half the element to stay cold while the other half heats, which is the classic failure that this replacement solves.
Does the element come with the mounting screws?
Yes, the kit includes the screws needed to secure the element to the oven floor, so nothing extra is required for the swap.
As an Amazon Associate, I earn from qualifying purchases.
